Manual Pages

Table of Contents


na_sysconfig - Displays node configuration information.


sysconfig [ -A | -a | -v | -c | -d | -h | -m | -p | -r -t | -V | -av ]

sysconfig [ -a | -v | -h | -av ] [ slot ]


sysconfig displays the configuration information about the node. Without any arguments, the output includes the Data ONTAP(tm) version number and a separate line for each I/O device on the node. If the slot argument is specified, sysconfig displays detail information for the specified physical slot; slot 0 is the system board, and slot n is the nth expansion slot on the node.


Displays all the sysconfig reports, one after the other. These include the report of configuration errors, disk drives, media changers, RAID details, tape devices, and aggregate details.

Displays very detailed information about each I/O device. This is more verbose than the output produced by the -v option. Disk sizes are scaled in GB. A GB is equal to 1000 MB (1024 * 1024 * 1000) or 1,048,576,000 bytes.

Displays very detailed information about each I/O device. This is the same output as the -a option except that the disk size values are scaled in size-related units, KB , GB , TB , whichever is most appropriate. The values will range from 1 to 999 to the left of the decimal point, and from 0 to 9 to the right of the decimal point. Unit values are based on powers of two; for example, one gigabyte is equal to (1024 * 1024 * 1024) or 1,073,741,824 bytes.

Checks that expansion cards are in the appropriate slots.

Displays vital product information for each disk.

Displays tape library information. To use this option, the autoload setting of the tape library must be off when the node boots.

Supported only on virtual platforms. Displays information about the physical host machine and its mapping to the virtual machine.

Displays RAID configuration information. The command output prints information about all aggregates, volumes, file system disks, spare disks, maintenance disks, and failed disks. See the vol and aggr commands for more information about RAID configuration.

Displays device and configuration information for each tape drive.

If you have a tape device that NetApp Inc has not qualified, the sysconfig -t command output for that device is different from that for qualified devices. If the node has never accessed this device, the output indicates that this device is a nonqualified tape drive, even though there is an entry for this device in the /etc/clone_tape file. Otherwise, the output provides information about the qualified tape drive that is being emulated by this device.

You can enter the following command to access a tape device:

mt -f device status

Displays detailed information about each I/O device. For SCSI or Fibre Channel host adapters, the additional information includes a separate line describing each attached disk.

Displays aggregate configuration information.


During normal operation, the sysconfig command displays similar information on a node in an HA pair as the sysconfig command on a standalone node. The output on a node in an HA pair, however, includes disks on both fibre channel loop A and loop B. The information about disks on loop B is for hardware only. That is, the sysconfig command only displays information about the adapters supporting the disks on loop B. It does not show the capacity of each disk on loop B or whether a disk on loop B is a file system disk, spare disk, or parity disk.

In takeover mode, the sysconfig command provides the same types of information as in normal mode, except that it also displays a reminder that the node is in takeover mode.

In partner mode, the sysconfig command does not display information about any hardware that is attached only to the partner. For example, if you enter the partner sysconfig -r command, you can obtain the software information about the disks on the partner. That is, for each disk on the partner, the command output indicates the capacity and whether the disk is a file system, spare, or parity disk. The command output does not include information about the disk adapters on the partner. The information about the disk adapters in the command output is for those on the local node.


na_aggr(1), na_partner(1), na_version(1), na_mt(1), na_vol(1)

Table of Contents