Manual Pages


Table of Contents

NAME

na_autosupport_trigger - Displays and modifies AutoSupport trigger configuration.

DESCRIPTION

autosupport trigger show - Displays AutoSupport trigger configuration.

autosupport trigger modify - Modifies AutoSupport trigger configuration.

USAGE

autosupport trigger show [ -fields ] [ -basic ] [ -troubleshooting ] [ -instance ] [ -autosupport-message ] [ -to ] [ -noteto ] [ -basic-default ] [ -troubleshootingdefault ] [ -additional-content ] [ -basic-additional ] [ -troubleshooting-additional ]

This command displays which system events trigger AutoSupport messages. When a trigger event occurs, the node might send an AutoSupport message to a predefined destination, and a short note to another destination. The full AutoSupport message contains detail for troubleshooting. The node sends the short message to pagers or as SMS text messages.

{ [-fields <fieldname>, ...]

With -fields <fieldname>, ... parameter, the command only displays the fields that you specify.

| [-basic]

Displays which subsystem information is included as basic information when the AutoSupport message is triggered.

| [-troubleshooting]

Displays which subsystem information is included as troubleshooting information when the AutoSupport message is triggered.

| [-instance] }

Displays detailed information about all entries.

[-autosupport-message] <Autosupport Message>] - EMS Message

Displays only AutoSupport triggers with the name specified. AutoSupport triggers are EMS messages whose names begin with "callhome.". However, for the purposes of this command, "callhome." is implied, does not need to be entered, and will not be displayed in command output.

[-to {enabled|disabled}] - Whether to deliver to options autosupport.to addresses

If -to is set to "enabled," displays only AutoSupport messages that send full messages to the "to" address when triggered.

[-noteto {enabled|disabled}] - Whether to deliver to options autosupport.noteto addresses

If -noteto is set to "enabled," displays only AutoSupport messages that send short notes to the "noteto" address when triggered.

[-basic-default <AutoSupport collection subsystems>, ...] - Default subsystems reporting basic info

Displays only AutoSupport triggers that include in their messages, by default, basic configuration content from the subsystems specified.

[-troubleshooting-default <AutoSupport collection subsystems>, ...] - Default subsystems reporting troubleshooting info

Displays only AutoSupport triggers that include in their messages, by default, detailed diagnostic content from the subsystems specified.

[-additional-content <Type of AutoSupport content>, ...] - Additional content flag

Displays only AutoSupport triggers that have been configured to include additional basic or troubleshooting content.

[-basic-additional <AutoSupport collection subsystems>, ...] - Additional subsystems reporting basic info

Displays only AutoSupport triggers that have been configured to include additional basic configuration content from the subsystems specified.

[-troubleshooting-additional
<AutoSupport collection subsystems>, ...] - Additional subsystems reporting troubleshooting info

Displays only AutoSupport triggers that have been configured to include additional detailed diagnostic content from the subsystems specified. Partner Hostname (if HA) CFO Node Status (if HA) cf monitor all output (if HA) ic stats performance output (if HA with VIA) ic stats error -v output (if HA with VIA) snet stats -v output (if HA with SNET) REBOOT (CF TAKEOVER)

autosupport trigger modify [ -autosupport-message ] [ -to ] [ -noteto ] [ -basic-additional ] [ -troubleshootingadditional ]

This command enables and disables AutoSupport messages for individual triggers, and specifies additional subsystem reports to include if an individual trigger sends an AutoSupport message.

[-autosupport-message <Autosupport Message>] - EMS Message

Specifies the AutoSupport trigger to modify. AutoSupport triggers are EMS messages whose names begin with "callhome.". However, for the purposes of this command, "callhome." is implied, does not need to be entered, and will not be displayed in command output.

[-to {enabled|disabled}] - Whether to deliver to options autosupport.to addresses

Use "enabled" to enable sending AutoSupport messages to the configured "to" address.

[-noteto {enabled|disabled}] - Whether to deliver to options autosupport.noteto addresses

Use "enabled" to enable sending short notes to the configured "noteto" address.

[-basic-additional <AutoSupport collection subsystems>, ...] - Additional subsystems reporting basic info

Includes basic configuration content from the additional subsystems specified. Content is collected from these subsystems in addition to the default list of subsystems.

[-troubleshooting-additional
<AutoSupport collection subsystems>, ...] - Additional subsystems reporting troubleshooting info

Includes detailed diagnostic content from the additional subsystems specified. Content is collected from these subsystems in addition to the default list of subsystems.

EXAMPLES

  The following example shows the first page of output from the command:

  node> autosupport trigger show

  AutoSupport                                       Additional
  Message                   To        Note To       Content
  ------------------------- --------- ------------- ---------------
  aggr.offline              enabled   enabled       -
  aggr.restricted           disabled  enabled       -
  aggr.wafliron             disabled  enabled       -
  bad.ram                   disabled  disabled      -
  battery.failure           enabled   enabled       -
  battery.low               disabled  disabled      -
  battery.notice            enabled   enabled       -
  battery.overchg           enabled   enabled       -
  battery.overtemp          enabled   enabled       -
  battery.warning           enabled   enabled       -
  bmc.bus                   disabled  disabled      -
  bmc.hb.stop               disabled  disabled      -
  bmc.post                  disabled  disabled      -
  bootfs.chkdsk             enabled   enabled       -
  c.fan                     enabled   enabled       -
  c.fan.fru.degraded        disabled  disabled      -
  c.fan.fru.fault           disabled  enabled       -
  c.fan.fru.rm              disabled  enabled       -
  c.fan.fru.shut            enabled   enabled       -
  carrier.fault             enabled   enabled       -
  ch.ps.degraded            disabled  disabled      -

  The following example enables messages from the battery.low trigger:

  node> autosupport trigger modify -autosupport-message battery.low -to enabled

SEE ALSO


Table of Contents